Creating a SED Secure Storage Pool
- Go to Storage & Snapshots > Storage > Storage/Snapshots.
-
Perform one of the following actions.
NAS State
Action
No volumes or storage pools
Click New Storage Pool.
One or more volumes or storage pools
Click Create, and then select New Storage Pool.
The Create Storage Pool Wizard window opens.
- Click Next.
- Optional:
Select an expansion unit from
the Enclosure
Unit list.
Important:
-
You cannot select disks from multiple expansion units.
-
If the expansion unit is disconnected from the NAS, the storage pool becomes inaccessible until it is reconnected.
-
-
Select Create SED secure storage
pool.
The list of disks only displays SED disks.
-
Select one or more disks.
Warning:
All data on the selected disks will be deleted.
-
Select a RAID type.
QTS displays all available RAID types and automatically selects the most optimized RAID type.
Number of disks
Supported RAID Types
Default RAID Type
One
Single
Single
Two
JBOD, RAID 0, RAID 1
RAID 1
Three
JBOD, RAID 0, RAID 5
RAID 5
Four
JBOD, RAID 0, RAID 5, RAID 6, RAID 10
RAID 5
Five
JBOD, RAID 0, RAID 5, RAID 6
RAID 6
Six or more
JBOD, RAID 0, RAID 5, RAID 6, RAID 10, RAID 50
Note:RAID 10 requires an even number of disks.
RAID 6
Eight or more
JBOD, RAID 0, RAID 5, RAID 6, RAID 10, RAID 50, RAID 60
RAID 6
Tip:Use the default RAID type if you are unsure of which option to choose.
For details, see RAID Types.
- Optional:
Select the disk that will be
used as a hot spare for this RAID group.
The designated hot spare automatically replaces any disk in the RAID group that fails.
For RAID 50 or RAID 60, a spare disk must be configured later. You should configure a global spare disk so that all subgroups share the same spare disk.
- Optional:
Select the number of RAID 50 or
RAID 60 subgroups.
The selected disks are divided evenly into the specified number of RAID 5 or 6 groups.
-
A higher number of subgroups results in faster RAID rebuilding, increased disk failure tolerance, and better performance if all the disks are SSDs.
-
A lower number of subgroups results in more storage capacity, and better performance if all the disks are HDDs.
Warning:If a RAID group is divided unevenly, the excess space becomes unavailable. For example, 10 disks divided into 3 subgroups of 3 disks, 3 disks, and 4 disks will provide only 9 disks of storage capacity.
-
- Click Next.
- Optional:
Configure SSD
over-provisioning.
Over-provisioning reserves a percentage of SSD storage space on each disk in the RAID group to improve write performance and extend the disk's lifespan. You can decrease the amount of space reserved for over-provisioning after QTS has created the RAID group.
Tip:To determine the optimal amount of over-provisioning for your SSDs, download and run SSD Profiling Tool from App Center.
- Optional:
Configure the alert threshold.
QTS issues a warning notification when the percentage of used pool space is equal to or above the specified threshold.
- Optional:
Configure pool guaranteed
snapshot space.
Pool guaranteed snapshot space is storage pool space that is reserved for storing snapshots. Enabling this feature ensures that QTS always has sufficient space to store new snapshots.
-
Specify the encryption
password.
The encryption password must consist of 8 to 32 characters from any of the following groups:
-
Letters: A to Z, a to z
-
Numbers: 0 to 9
-
Special characters: Any except for space ( )
Warning:Remember this password. If you forget the password, the pool will become inaccessible and all data will be unrecoverable.
-
- Optional:
Save the encryption key
to the local NAS.
Saving the encryption key enables QTS to automatically unlock and mount the SED pool when the NAS starts up. If the encryption key is not saved, you must specify the encryption password every time the NAS restarts.
Warning:Enabling this setting can result in unauthorized data access if unauthorized personnel are able to physically access the NAS.
- Click Next.
-
Click Create.
A confirmation message appears.
- Click OK.
QTS creates the storage pool and then displays the information on the Storage/Snapshots screen.